发布时间 : 星期日 文章Dell戴尔 PowerEdge R720 服务器错误代码二更新完毕开始阅读
The temperature for power supply
错误代码 消息信息 LCD 消息
PSU
An under voltage fault detected on power supply
An under voltage fault detected on PSU
2.检查系统中的线缆和子系统组件以排查损坏。 3.如果问题仍然存在,请参阅“获得帮助”。 PSU0035消息
An over voltage fault detected on power supply
Over voltage fault on PSU
An over current fault detected on power supply
2.检查系统中的线缆和子系统组件以排查损坏。 3.如果问题仍然存在,请参阅“获得帮助”。 PSU0037消息
Fan failure detected on power supply
Fan failure detected on PSU
A power supply wattage mismatch is detected; power supply
错误代码 消息信息 LCD 消息
PSU wattage mismatch; PSU
Power supply redundancy is lost.(电源设备冗余缺失。)详细信息电源设备尝试在降级状态下运行。系统性能和电源冗余可能降级或缺失。 操作检查输入电源。重新安装电源设备。如果问题依然存在,请参阅“获得帮助”。 PSU1204消息
The power supplies are not redundant. Insufficient resources to maintain normal operations.(电源设备并非冗余。维持正常运行的资源不足。) LCD 消息
PSU redundancy degraded. Check PSU cables.(PSU 冗余降级。检查 PSU 电缆。)详细信息当前电源可操作模式并非冗余,原因是电源设备异常、电源设备资源变化,或系统电源资源变化。操作检查事件日志排查电源设备故障。查看系统配置和功耗。 PWR1004消息
The system performance degraded because power capacity has changed.(因为电源容量变化系统性能已降级。)详细信息系统可能关闭或在性能降级的状态下运行。操作检查事件日志排查电源设备故障。查看系统配置和功耗,并据此升级或安装电源设备。 PWR1005消息
The system performance degraded because the user-defined power capacity has changed.(因为用户定义的电源容量已变化,系统性能已降级。)详细信息用户定义的电源设置影响系统运行。操作如果是意外导致,查看系统配置变化和电源策略。
PWR1006消息因为系统电源超出容量,系统已停止。 LCD 消息
System power demand exceeds capacity. System halted.(系统电源需求超出容量。系统已停止。)详细信息因为系统电源超出容量,系统已停止。操作查看系统配置,升级电源设备或降低系统功耗。 RFM1008消息
Failure detected on Removable Flash Media
Removable Flash Media
错误代码 消息信息
操作重置闪存介质。如果问题仍然存在,请参阅“获得帮助”。 RFM1014消息 Removable Flash Media
Removable Flash Media
Internal Dual SD Module redundancy is lost.(内部双 SD 模块冗余缺失。) LCD 消息
Internal Dual SD Module redundancy is lost. Check SD Card.(内部双 SD 模块冗余缺失。检查 SD 卡。)详细信息其中一块或两块 SD 卡工作不正常。操作请参见“获得帮助”。 RFM2001消息 Internal Dual SD Module
Internal Dual SD Module
Internal Dual SD Module
Failure detected on Internal Dual SD Module
Internal Dual SD Module
SD 卡模块已安装,但配置不正确,或无法初始化。 操作重新安装 SD 模块,然后卸下并重新安装 SD 卡。 RFM2006消息 Internal Dual SD Module
错误代码 消息信息 SEC0031消息
The chassis is open while the power is on.(电源开启状态下机箱打开。) LCD 消息
Intrusion detected. Check chassis cover.(检测到侵入。检查机箱盖。)详细信息机箱打开。系统性能可能降级,安全性可能无法保证。操作关闭机箱。检查系统日志。 SEC0033消息
The chassis is open while the power is off.(电源关闭状态下机箱打开。) LCD 消息
Intrusion detected. Check chassis cover.(检测到侵入。检查机箱盖。)详细信息电源关闭状态下机箱打开。系统安全性可能已被破坏。操作关闭机箱并验证硬件资源。检查系统日志。 SEL0006消息
All event logging is disabled.(所有事件日志已禁用。)详细信息当用户禁用所有事件日志时将显示此消息。操作若是意外导致,则重新启用日志。 SEL0008消息
Log is full.(日志已满。)详细信息当日志已满时,其他事件将不会写入到日志。早期的事件可能被覆盖并丢失。如果用户禁用了事件记录,也可能显示此消息。操作备份并清除日志。 SEL0012消息
Could not create or initialize the system event log.(无法创建或初始化系统事件日志。)详细信息如果系统事件日志初始化失败,将不会捕获平台状态和故障事件。某些管理软件不会报告平台异常。操作重新引导管理控制器或 iDRAC。关闭然后打开输入电源。如果问题仍然存在,请致电支持部门。 SEL1204消息 An unknown system hardware failure detected.(检测到未知系统硬件故障。) LCD 消息
Unknown system hardware failure.(未知系统硬件故障。)详细信息如果系统事件日志初始化失败,将不会捕获平台状态和故障事件。某些管理软件不会报告平台异常。操作将系统重新配置为所支持的最低配置,如果问题仍然存在,请联系支持部门。 TMP0118消息
The system inlet temperature is less than the lower warning threshold.(系统进气孔温度低于下限警告阈值。) LCD 消息 System inlet temperature is outside of range.(系统进气孔温度超出范围。)详细信息环境气温过低。操作检查系统运行环境。 148
错误代码 消息信息 TMP0119消息
The system inlet temperature is less than the lower critical threshold.(系统进气孔温度低于下限临界阈值。) LCD 消息 System inlet temperature is outside of range.(系统进气孔温度超出范围。)详细信息环境气温过低。操作检查系统运行环境。 TMP0120消息