发布时间 : 星期六 文章ISE实现多功能数字钟设计更新完毕开始阅读
assign
ENM_H=(Adj_Min&&(TMinute[3:0]==4'h9))||(TMinute[3:0]==4'h9)&&(TSecond==8'h59);//24小时制
counter24 H0(Hour_24[7:4],Hour_24[3:0],nCR,ENH,EN,CP_1Hz);
assign
ENH
=
Adj_Hour?Vdd:((TMinute==8'h59)&&(TSecond==8'h59));
//===========12小时与24小时进制切换控制==========
assign
Display_HourAdjust=((Hour_24==8'h20)||(Hour_24==8'h21))?(Hour_24-24):(Hour_24-18);
assign Hour_12 = (Hour_24<8'h13)?Hour_24:Display_HourAdjust; assign Display_HourT = Hchange?Hour_12:Hour_24; //===========闹钟============ //----------时钟秒---------
//counter60 CCS(nCR,CP_1Hz,EN,CSecond[7:4],CSecond[3:0]); //----------时钟分---------
counter60 CCM(nCR,CP_1Hz,CMin_EN,CMinute[7:4],CMinute[3:0]); //--产生分使能信号--
assign CMin_EN = (!EN && Adj_Clock && Adj_Min); //----------时钟时---------
Counter24C CCH(nCR,CP_1Hz,CHour_EN,CHour[7:4],CHour[3:0]); //--产生时使能信号--
assign CHour_EN = (!EN && Adj_Clock && Adj_Hour); //--闹钟响--
always@(EN or Clock_EN) //闹钟开关 begin
if(EN && Clock_EN && (CHour == Display_HourT) && (CMinute ==
TMinute))Alarm <= 1;
else Alarm <= 0;
end
always@(posedge CLK_50 or negedge EN or negedge Alarm) //表示闹钟
的LED
begin
if(~EN) Led_Alarm <= 0; else begin
if(~Alarm) Led_Alarm <= 0; else Led_Alarm <= ~Led_Alarm;
end
end
//alarm_clock
AL0(Hour24,Minute,CP_1Hz,Set_Alarm,Close_clock,nCR,KeySet_Hour_ev,KeySet_Minute_ev,LD_7,Alarm_Hour,Alarm_Minute);
//===========数码显示=========
always@(Adj_Clock)//确定数码管显示闹钟还是正常时钟
begin
if(Adj_Clock) begin Display_Hour <= CHour;Minute <= CMinute;end else begin Display_Hour <= Display_HourT;Minute <= TMinute;end
end
always@(posedge CP_200Hz) begin
if(Change==1)
begin
case(HEX)
4'b1110: begin HEX<=4'b0111; bcd<= Display_Hour
//数码管进行时分显示
[7:4]; end //第一根数码管显示小时十位
4'b0111: begin HEX<=4'b1011; bcd<= Display_Hour
[3:0]; end //第二根显示小时个位
4'b1011: begin HEX<=4'b1101; bcd<= Minute [7:4];
end
//第三根显示分钟十位
4'b1101: begin HEX<=4'b1110; bcd<= Minute [3:0];
end
//第四根显示分钟个位
default: begin HEX<=0111; bcd<=Display_Hour [7:4]; end endcase
end
//数码管进行秒显示,change为低电
else
平时显示秒
begin
case(HEX)
4'b1110: begin HEX<=4'b1101; bcd<= TSecond [7:4];
end
//第三根显示秒十位
4'b1101: begin HEX<=4'b1110; bcd<= TSecond [3:0];
end
//第四根显示秒个位
default: begin HEX<=1101; bcd<= TSecond [7:4]; end endcase
end
end
SEG7_LUT L0(HEX0,bcd);
//调用数码管子函数
//======整点报时========== assign LD_6 = LD_6_RADIO;
always@(CP_1Hz) begin
==
8'h00)
&&
(counter[7:0]
<
if((Minute[7:0] (Hour_24[7:4]*10 + Hour_24[3:0])))
begin
LD_6_RADIO <= CP_1Hz;
end
else