发布时间 : 星期三 文章锡膏印刷机mpm-1中文教材更新完毕开始阅读
Teach Teach Board Teach Vision Device Layout Teach ID Teach Custom BGA Teach Offset Moves Teach Vision Offset Teach Board Teach Vision Device Layout Teach ID Teach Custom BGA Teach Offset Moves Teach Vision Offset 做一片PCB板新程序 做一片PCB新程序的Mark点 做2D检查时,所要检查零件 做辨识钢板身分 编辑自行设计的BGA零件档案 设定”印刷前的焊垫”与” 印刷后的焊垫”位置修正值 设定”视觉系统” 位置修正值 1.Teach Board重做新程序
About to begin TEACH operation(开始设定操作)
Press SELECT to teach a new board or(按SELECT,设定新基板)
Press NEXT to continue on this board setup (按NEXT,继续这基板的设定)
按SELECT之后，出现下列讯息窗口：
CAUTION, The machine must move to TEACH POSITION before teach can begin The machine is now going to move.
Press NEXT to Continue, or EXIT to Quit.
CAUTION, The machine must move to(警告,设定开始前,机器必须移动到 TEACH POSITION before teach can begin”设定位置”) The machine is now going to move. (机器即将移动)
Press NEXT to Continue, or EXIT to Quit. (按NEXT继续, 按EXIT离开)
1.1 选择Board Parameters 进入PCB参数设定 Board Parameters Hardware Required:
Board Board Parameters X size Thickness
228.600 1.570 Y size 406.400 基板(PCB)参数设定 (PCB)基板X轴方向长度 (PCB)基板Y轴方向宽度 (PCB)基板厚度 PCB板 Y X Enter Board Dimensions into setup menu.
Click on Y size to adjust Track Width.
Press Done when finished.
Enter Board Dimensions into setup menu. (输入基板X、Y、厚度)
Click on Y size to adjust Track Width. (点取Y方向尺寸，可调整轨道宽度) Press Done when finished. (当你做完上述之步骤，按Done)
点取X size，输入基板宽度X size，按EXIT完成输入，单位mm。
例14.5cm = 145mm
点取Y size输入基板宽度Y size，按EXIT之后出现如下讯息窗口： About to adjust the TRACK WIDTH for the board. Press NEXT to Continue, or EXIT to Quit.
About to adjust the TRACK WIDTH for the board. (调整基板的轨道宽度) Press NEXT to Continue, or EXIT to Quit. (按NEXT继续, 按EXIT离开)
按NEXT之后，出现下列讯息窗口：
This is the current Track width Press SELECT to fine adjust Press NEXT to accept
This is the current Track width(这是目前的轨道宽度) Press SELECT to fine adjust (按SELECT微调轨道宽度) Press NEXT to accept(按NEXT，接受目前的轨道宽度)
如果，你按SELECT之后，出现下列讯息窗口： Jog ACTIVE…
TRK WIDTH 126.136
Press NEXT to quit(调整完后，按EXIT)
Jog ACTIVE…(这段讯息告诉你，用Jog方式去调整基板的轨道宽度) TRK WIDTH 126.136
Press NEXT to quit(调整完后，按NEXT)
点取Thickness，输入基板厚度。使用光标卡尺测量。
Press Done when finished. (当你做完上述之步骤，按Done) Stencil Dimensions Inner 660.400 钢板尺寸设定参数 钢板尺寸
Enter stencil inner dimension Press Done when finished.
Enter stencil inner dimension(输入内部钢板尺寸)
Press Done when finished. (当你做完上述之步骤，按Done)
1.2 选择Worknest 进入印刷工作平台参数设定 Worknest Hardware Required: Board ,Tactile , Vacuum Chucks
Please remove the stencil. Squeegee will now move back. Press SELECT when ready.