发布时间 : 星期日 文章数通高培实验指导书ISSUE 1.0更新完毕开始阅读
数通高培工程师实验指导书ISSUE1.0
学员用书
0 errors, 6596240 CRC, 0 giants Output:390 packets, 7324 bytes, 0 underruns 0 MulticastPkts, 0 MulticastBytes 0 CRC, 0 aborted sequences, 0 giants
[router-B]display pos interface pos5/0/0:1 Pos5/0/0:1 current state: up Line protocol current state: up Physical layer is Packet over SDH Card info: POS OC-48/STM-16-SM-SR-LC
Line Type: SingleMode, WaveLength: 1310nm, Transmission Distance: 2km
Average Optical Output Power: -10~-3 (dBm) Receiver Overload: -3 (dBm)
Optical Center Wavelength: 1310 (nm) Receiver Sensitivity: -18(dBm)
Description: HUAWEI, Quidway Series, Pos5/0/0:1 Interface Internet address is 1.1.1.2/24 Is-Primary
The Maximum Transmit Unit is 4470 bytes, the BandWidth is 155000 Kbps Loopback not set, Clock source master, Scramble enabled, Urpf disabled Link-protocol is PPP
MRU: 4470 bytes, Negotiate Timeout set 3 seconds Peer MRU: 4470 bytes, Magic number: 83911574 Peer IP address is 1.1.1.1/32 LCP: Opened
NCP: IPCP Opened, MPLSCP Opened
Input: 336 Lcps, 42 Ipcps, 3 Mplscps, 0 Osicps, 40 Invalids Output:430 Lcps, 2 Ipcps, 2 Mplscps, 0 Osicps, 0 Invalids
华为技术有限公司 版权所有, 未经许可不得扩散
23
数通高培工程师实验指导书ISSUE1.0
学员用书
Hold time is 10 (sec)
Input: 323 Timerhold Packets Output:322 Timerhold Packets Statistics last cleared: never Traffic statistics:
Last 5 minutes input rate 3 bytes/sec, 0 packets/sec Last 5 minutes output rate 3 bytes/sec, 0 packets/sec Input: 6596631 packets, 277105069 bytes 0 MulticastPkts, 0 MulticastBytes 0 errors, 6596240 CRC, 0 giants Output:444 packets, 8188 bytes, 0 underruns 0 MulticastPkts, 0 MulticastBytes 0 CRC, 0 aborted sequences, 0 giants
SECTION: Seconds Count
B1 0 0 LOS 0 0 OK LOF 0 0 OK OOF 0 0 OK SES 0 0
SSEFS 0 LINE:
B2 0 0 LREI 0 0 OK LRDI 0 0 OK LAIS 0 0 OK SFBERR 0 0 OK SDBERR 0 0 OK
24
华为技术有限公司 版权所有, 未经许可不得扩散
数通高培工程师实验指导书ISSUE1.0
学员用书
LES 0 LSES 0 LUAS 0 LFEES 0 LFESES 0 LFEUAS 0 PATH:
B3 0 0 PREI 0 0 OK PLOP 0 0 OK PAIS 0 0 OK PRDI 0 0 OK PPLM 0 0 OK PES 0 PSES 0 PUAS 0 PFEES 0 PFESES 0 PFEUAS 0 CLOCK RECOVERY: RDOOL OK RROOL OK TROOL OK Rxd: 0 packets
0 FCS, 0 aborts, 0 Max, 0 Min Txd: 0 packets
0 underruns, 0 aborts SDH overhead:(Rx/Tx)
F1 : NA/NA , J0 : 0x4e/0x4e, K1 : 0x00/0x00, K2 : 0x00/0x00
华为技术有限公司 版权所有, 未经许可不得扩散
25
数通高培工程师实验指导书ISSUE1.0
学员用书
S1 : 0x08/0x08, C2 : 0x16/0x16, F2 : NA/NA , Z3 : NA/NA Z4 : NA/NA , V5 : NA/NA
Received section trace(J0): \
4e 65 74 45 6e 67 69 6e 65 20 20 20 20 20 20 00 NetEngine Received path trace(J1): \
4e 65 74 45 6e 67 69 6e 65 20 20 20 20 20 20 00 NetEngine Transmitted section trace(J0): \
4e 65 74 45 6e 67 69 6e 65 20 20 20 20 20 20 00 NetEngine Transmitted path trace(J1): \
4e 65 74 45 6e 67 69 6e 65 20 20 20 20 20 20 00 NetEngine 3、需要进行ppp验证请参照POS接口的ppp验证配置
2.5 E1/CE1接口的配置 实验环境： POS?ó?ú????1.1.1.0/24A.1.2B CPOS接口配置上机组网图 （1）、路由器A和路由器B采用E1接口进行互连 1、 进入E1接口(控制口)，配置相关物理参数 RouterA物理层的参数采用缺省参数： 设置E1接口的线路编解码格式：code hdb3 设置E1接口的时钟模式：clock master 设置E1接口的环回方式：undo loopback 激活E1/CE1通道：using e1 RouterB物理层的参数配置：
26
华为技术有限公司 版权所有, 未经许可不得扩散