QC验货指南 联系客服

发布时间 : 星期日 文章QC验货指南更新完毕开始阅读

2,如果一次验货包括2款以上,请在报告第一页列出 ARTICLE NUMBER/PO NUMBER,避免用\REMARK X\代替(除非5款以上),而对于\要给出概括性的描述,如\以方便客人知道验的是什麽产品.

Thanks for your attention!

Eric.Wu Dec 29,2005 28)

Dear All

Please be noted:

1)WEEE SYMBOL 出现在下列任何地方都是可以接受的:

PRODUCT/RATING LABEL/CORD LABEL/INSTRUCTION/WARRANTY/PACKAGING

2)验货结果如果是ON HOLD/REJECTED,请当天一定通知SZ OFFICE,特别是与工厂意见不一致的情况下,一定不要和工厂争执,征询过SZ MANAGER 意见后再做决定

3)HOME BASE的报告一定要当天传到UK,周一至周五如 5:30前传回公司, 我会负责扫描给UK,但5:30之后没传回 的报告还请自己传,周六也要自己传.

TO :DANIEL.BARCLAY FAX:00 44 118 9398708

For PASS report please send page 1 only

For ON HOLD reports please send PAGE 1 & Remarks

For FAIL reports please send all the report. 29)

Dear All

Attached please find a list of Homebase vendors that belong to ARGOS HK,

For the inspections to these vendors, one draft report copy must be left to the factory after inspection.

For the inspections that belong to UK(not included in this list), please do not leave draft report copy to factory.

Thanks and best regards! Eric.Wu Jan 18,06 30)

Page 21 of 40

Dear All

Please pay attention to this point during inspection,

Thanks !

Eric.Wu Jan 19

----- Original Message ----- From: Mousse Chan (HL) Dear Eric/ Kaddy/ Skally/ Lydia / Kevin,

I am not sure if Ivan refers to Argos or Homebase report. In order to avoid such mistake happen, pls follow the steps as follow and inform inspectors accordingly.

1) Draft written report:

Inspectors have been instructed to copy down - actual weight and the actual dimension 2) Photos:

-Inspectors shall take clear photos to show the gross weight and dimension show on shipping mark.

3) Final report:

-STR should review the final report against the draft report

a) If actual weight and actual dimesnion are copied down on the draft report

b) For Argos report - Discrpency more / less than 5% between the actual weight / dimension and the shipping mark (weight / dimension) - ON HOLD report should be

issued. - Discrpency more / less than 5% between the actual weight /

dimension or the shipping mark information and the given information on specification - pls put this on remark part.

For HB report - Pls mark down any discrepency found between the actual weight / dimension, shipping mark (actual weight / dimension) or specification (actual weight / dimension) on the reamrk part - NO need to ON HOLD

Thanks and best regards, Mousse Chan 31) 32)

Dear All

When inspect the products with lighting chain, please :

Page 22 of 40

1)record down the measured power consumption, current voltage information on the report.

2)If the measured power with more / less than 10% deviation with the given power, inspection result should be marked as FAIL.

3)the endurance test must be run 8 hours on 240V. ( At least 3 pieces)

Thanks !

Eric.Wu Jan 27,06 33)

Dear All

因为经常出现HOME BASE草稿报告没有当天传的情况,现对传真程序做如下修改:

1)对于HOMEBASE验货 ,请当天一定把整份草稿报告传回深圳OFFICE,无论结果是PASS/ON HOLD 还是REJECTED,我会统一发给STR UK和ARG HK.

2)但如果验货无法于5:30PM前完成,(或在周末),请亲自传真到UK 或 ARG HK, (PASS 报告传PAGE 1,ON HOLD/REJECTED 传整份)

属于UK的传到0044-1189398708(TO:DAN.Barclay),

属于ARG HK的传真到00852-27242009(TO:IRENE.WONG/ELPIS.SO)

***请务必亲自传真报告回公司,并确认OFFICE收到后才离开, 请注意工厂人员没有义务帮忙我们传报告

另外,属于ARG HK的验货一定要留草稿报告COPY给工厂. 附件中列表全是属于ARG HK的的VENDOR.

THANKS FOR YOUR ATTENTION! Eric.Wu Feb 10,06 34)

Dear All

因我司检验的产品出现无法组装的问题,请大家在将来的验货中必须遵照如下指南来进行组装测试(ASSEMBLY TEST) 附件中有更详细的解释:

The requirement of furniture assembly test

(家具组装测试要求)

Page 23 of 40

For all the furniture being required to assembly before using, Inspectors should assemble the products by themselves acting as an end user without any guidance or special tricks from the factory, and strictly follow the assembly instructions taking into the consideration of the possible assembly methods, even the worst condition by an end user. If any abnormal conditions were found, or special tricks shall be employed during assembly, inspectors should report as such on the report and hold the shipment. Of course how many products assembled and build quality should be remarked on the report as usual.

对于任何使用前需要组装测试的家具等产品,验货员都必须以最终消费者的身份,严格按照组装说明书,亲自组装,不得听取工厂的指导或是采用特殊技巧,并且要考虑最终消费者可能遇到的各种组装方法。在如上述的组装过程中,如有发现任何异常,或是要采用特殊技巧,验货员都应该如实汇报,并且hold结果。当然,要按照惯例对于组装的产品数量和组装后的质量如实备注于报告中.

Feb10,2006 35)

Dear All

从现在开始,ARGOS/HOMEBASE 检验电器/电子产品时,报告中必须附上电器配件的核查表,见附件.填写完后随草稿报告一起传回公司.

表格中属于TYPE(A)的配件是可替换配件,但是,替换配件的各项电器指标必须和客户资料中指定配件的电器指标一致,而且该替换配件必须有相关证书(CERTIFICATE),才可以接受,

TYPE(A)--如果替换配件能提供相关证书但电器指标不完全符合,就要研究过再作决定(CASE BY CASE)

表格中属于TYPE(B)的配件必须和客户资料一致, 如果不符合,报告结果就要ON HOLD

表格的填写方法:

验货中产品的所有电器配件(如PLUG/FUSE/POWER CORD/LAMP HOLDER...)都要列入表格中, 在\栏填写序号,

在\栏填写配件的电器指标,

如果实际配件和客户资料一致,就在\栏化圈表示符合,

如果实际配件的指标和客户资料不一致,就在\和\

SPECIFICATION \分别填写,然后在\栏化圈或叉表示电器指标符合/不符合,在\栏化圈或叉表示是否提供了相关证书

*另外,因为各电器配件的详细情况已经在此表格中出现,在报告的REMARK中可以不再重复.

Page 24 of 40